Digi-Sense 60010-85 Spezifikationen

DataLogRRTD THERMOMETERMODEL NO. 60010-85Digi -Sense ® Digi -Sense ® Digi -Sense ® Blk 55 Ayer Rajah Crescent#04-16 Singapore 139949Tel: (65) 677

8CONNECTING AN RTDNote: Be sure your instrument setting matches theRTD you are using (alpha of 0.00385 or 0.003916).See SELECTING RTD SENSITIVITY (ALP

9

10

11

12QUICK SETUPNote: Review SAFETY PRECAUTIONS on page 3.1. Install batteries.2. Connect RTD probe.3. Press the ON/OFF key. The thermometer performsa se

13If a probe has not yet been connected to theinstrument, you will see this display:This message also appears if a probe is broken.No measurements can

14COMPLETE SETUP PROCEDUREThe setup function scrolls through a series of stepsfor selecting probe sensitivity (alpha), resolution, filterrate, setting

15the greatest possible resolution. The next choice is0.1° resolution: the thermometer will automaticallyrange between 0.1° and 1° as required. The fi

163. The left two digits in the lower left display willbe flashing. Use the MAX ▲▲▲▲▲ key or MIN ▼▼▼▼▼ keyto adjust the flashing digits to the desired

17The lower left display will show “LINE” while theupper display is flashing either 50 or 60. Use theMAX ▲▲▲▲▲ key or MIN ▼ ▼ ▼ ▼ ▼ key to adjust the

CERTIFICATE OFCONFORMANCEThis thermometer was calibrated usingequipment traceable to the National Insti-tute of Standards and Technology (NIST).This i

18PRINT SETUPThe Print sub-menu is used to set the time intervalsbetween the readings being sent to the printer. Thedefault rate is once every three s

19OPERATING PROCEDURESThe unit will always power up with the upperdisplay showing temperature. If a probe is notconnected at power up, the upper displ

20Clearing a Maximum ReadingPress the CLEAR key then press the MAX ▲▲▲▲▲ key.The maximum memory will be cleared.MINIMUM READINGSThe minimum reading fu

21Minimum HoldPress the MIN ▼▼▼▼▼ key, then press the HOLD key. To turn off the HOLD function and return tonormal operation press the HOLD key again.

22RECALL READINGSThis function allows the stored readings, thereading sequence number and the Time/Dateof the readings to be recalled. RECALL showseac

23LOGGING READINGSThe Logging function is controlled by the LOG key.Prior to logging readings, it is necessary to set upthe time interval between read

24Printer Format for Normal PrintingNew heading will appear when date changes ornew print is started.---- = over range06/01/00 °F13:20:54 30.5613:

25Printer Format for Log DumpNew heading will appear when date changes.---- = over rangeTOTAL READINGS:100002/02/00 °F19:01:00 ----19:01:02 -3

26RS-232-C Format for Normal Printing and LogDump---- = over range“DATE”, “TIME”, “DEGREES F”07/13/00,16:30:20, 72.56,16:30:30, 72.55,16:30:40, “OPEN”

27Printer output will occur in real-time when thethermometer is operating in the normal mode. Whenthe thermometer is in the RECALL mode, printingof th

1INTRODUCTIONThis versatile hand-held instrument provides highlyaccurate temperature measurements in Celsius orFahrenheit using a 100 ohm platinum RTD

28Other liquids may also be used as calibrationstandards. Consult a chemical handbook for theirfreezing (melting) point and boiling point properties.W

293. Allow the reading to stabilize. If the displayedtemperature is higher or lower than the referencetemperature, use the MAX ▲ ▲ ▲ ▲ ▲ key to increa

30Lockout Procedure1. Turn the thermometer off.2. Simultaneously press and hold the CAL and theCLEAR keys down and momentarily press theON/OFF key. Co

31while changing the batteries. All stored/loggedreadings are retained until cleared, even if thebatteries are removed for long periods.SERVICEThere a

32TROUBLESHOOTINGThe following chart lists the most probable faults.There are no internal adjustments or user-replaceable parts. If this does not solv

WARRANTYThe Manufacturer warrants this product to befree from significant deviations from publishedspecifications. If repair or adjustment is neces-sa

2• Scrolls through all stored readings• Displays MIN and MAX readings• Interfaces with optional HEWLETT PACKARD®infrared printer or optional RS-232-C

3EU Declaration of ConformityName of Apparatus: RTD LoggerModel Number: 60010-85*Description of Apparatus: Electronic thermometerusing an RTD probeBar

4SPECIFICATIONSRTD PROBESImpedance: 100 ohm @ 0°C (32°F)Sensitivity (alpha): 0.003850 or 0.003916 ohm/ohm/°C selectableAccuracy: ±0.06°F; ±0.03°C at 0

5Dimensions3 cm D x 8.4 cm W x 15.8 cm H(1.2 in x 3.3 in x 6.2 in)Weight with batteries: 227 grams (8 ounces)Ingress protection: Meets IEC-529 IP-54 f

6BATTERY INSTALLATION ANDREPLACEMENTVOLTAGES PRESENT ATTHE RTD MAY ALSO BEPRESENT AT THE BATTERY TERMINALS.ALWAYS DISCONNECT THE RTD WHENCHANGING BATT

7If battery indicator turns on, battery life isapproximately 8 to 10 hours. The battery indicatorwill start blinking with less than 1 hour of liferema